Matrix E5x-02 Especificaciones

E5X-03 SUSPENSION ELLIPTICAL SERVICE MANUALE5X-04 SUSPENSION ELLIPTICALSERVICE MANUAL

7WORKOUTKEYS: Simple program view and selection buttons. Go: One touch Start. enter: To confirm each program setting. uP / DoWn leVel: Easy info

84.2 WORKOUT SETUP STEPS - MANUAL 4.4 WORKOUT SETUP STEPS - LEVEL BASEDCHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTIONGo - Press to immediately beg

94.5 WORKOUT SETUP STEPS - COOPER FITNESS TESTCHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTIONFitness test -The Cooper Fitness Test measures cardiov

104.6 WORKOUT SETUP STEPS - TARGET HEART RATE 4.7 WORKOUT SETUP STEPS - CONSTANT WATTSCHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTIONtarGet Heart r

11The Manager's Custom Mode allows the club owner to customize the Suspension Elliptical for the club. 1) To enter Manager Mode, press and hold

125.2 MANAGER MODE INFORMATION CUSTOM SETTING DEFAULT MINIMUM MAXIMUM DESCRIPTIONMaximum Time 60 min 5 min 99 min Sets the total run time of any prog

136.1 USING ENGINEERING MODETo enter Engineering Mode, hold the LEVEL UP and DOWN keys for 3-5 seconds until Manager Mode appears on the middle LED di

147.1 USING SERVICE MODETo enter Service Mode, hold the LEVEL UP and DOWN keys for 3-5 seconds until Manager Mode appears on the middle LED display.

158.1 ELECTRICAL DIAGRAMSCHAPTER 8: TROUBLESHOOTINGHURES5X-C ELECTRICAL BLOCK DIAGRAM

168.1 ELECTRICAL DIAGRAMS - CONTINUEDPULSE SENSOR WIRECHAPTER 8: TROUBLESHOOTING

CHAPTER 1: SERIAL NUMBER LOCATION ... 1CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS 2.1 Read and

178.1 ELECTRICAL DIAGRAMS - CONTINUEDCHAPTER 8: TROUBLESHOOTINGDIGITAL COMMUNICATION WIREDIGITAL COMMUNICATION WIREE5X-F ELECTRICAL BLOCK DIAGRAM

18POWER RESISTANCE WIREECB WIRE8.1 ELECTRICAL DIAGRAMS - CONTINUEDCHAPTER 8: TROUBLESHOOTING

198.2 ERROR CODES ON THE CONSOLECODE CLASS DESCRIPTION SOLUTION0x02AB C Machine type error. Set the correct machine type in Engineering Mode. 0x02B4

208.3 LCB LED INDICATORSCHAPTER 8: TROUBLESHOOTING====================== FIRMWARE DEFINITION ========================LED6: LCB STATUS (BLINKING: OK)LE

218.4 LCB1_ERP WIRING CONNECTIONCHAPTER 8: TROUBLESHOOTING

228.5 TROUBLESHOOTING - ERROR 04A0CHAPTER 8: TROUBLESHOOTINGFIGURE A FIGURE BERROR CODE 04A01) SYMPTOM:04A0 – PCB communication disconnected.2) SOLU

238.6 TROUBLESHOOTING - ERROR 04B0CHAPTER 8: TROUBLESHOOTINGFIGURE A FIGURE BERROR CODE 04B01) SYMPTOM:04B0 – LCB communication disconnected.2) SOLU

24CHAPTER 8: TROUBLESHOOTING8.7 TROUBLESHOOTING - ERROR 0248FIGURE A FIGURE BERROR CODE 02481) SYMPTOM:0248 –Battery disconnection or fail. (When the

25FIGURE AFIGURE BCHAPTER 8: TROUBLESHOOTING8.8 TROUBLESHOOTING - ERROR 02B4ECB use on SC5x frame and EP84 (ECB system E5x).Resistor use on HUREA5x fr

26CHAPTER 8: TROUBLESHOOTING8.9 TROUBLESHOOTING - ERROR 02ABFIGURE A FIGURE BMachine type is E5x-02 Machine type is E5x-03 ERROR CODE 02AB1) SYMPTOM

III9.8 Drive Axle Set Replacement ... 429.9 Crank Replacement ..

27CHAPTER 8: TROUBLESHOOTING8.10 TROUBLESHOOTING - ERROR 01ACFIGURE AERROR CODE 01AC1) SYMPTOM:01AC - Resistance over current. 2) SOLUTION:1) Chec

28CHAPTER 8: TROUBLESHOOTING8.11 TROUBLESHOOTING - NO RESISTANCE ISSUEFIGURE A FIGURE BFIGURE A FIGURE BNO RESISTANCE TROUBLESHOOTING 1) SYMPTOM:No r

298.12 TROUBLESHOOTING - HEART RATE ISSUESCHAPTER 8: TROUBLESHOOTINGHEART RATE FUNCTION DOES NOT WORK OR IS READING INCORRECTLYPOSSIBLE CAUSES:1) The

308.13 TROUBLESHOOTING - NO POWER TO THE CONSOLEPOWER SWITCH IS ON, BUT THE CONSOLE HAS NO DISPLAYPOSSIBLE CAUSES:1) The unit is not getting power fr

31ALL OR SOME OF THE FUNCTION KEYS DO NOT RESPONDPOSSIBLE CAUSES:1) The keypad connection ribbon cable has not been plugged in correctly. 2) The ke

329.1 FRONT DISK REPLACEMENT 1) Remove the center cover by turning it counter clockwise (Figures A & B). 2) Remove the 3 screws holding the dis

339.2 FRONT SHROUD REPLACEMENT 1) Remove the link arm and pedal arm plastic caps (Figures A & B). 2) Detach the dual action handlebar from the

349.2 FRONT SHROUD REPLACEMENT - CONTINUED7) Pull out the rubber tray from the cup holder plastic (gure G). 8) Remove the 2 screws to disassemble

359.2 FRONT SHROUD REPLACEMENT - CONTINUED12) Remove the 9 screws to detach the front shrouds from the frame (or each other) (Figure M). 13) Turn t

369.3 LOWER CONTROL BOARD REPLACEMENT1) Turn off the power and disconnect the cord from the machine.2) Remove both front disks from the machine as

11.1 SERIAL NUMBER LOCATIONSERIAL NUMBER LOCATIONCHAPTER 1: SERIAL NUMBER LOCATION

379.4 GENERATOR REPLACEMENT1) Turn off power and disconnect the cord from the machine.2) Remove the front disks as outlined in Section 9.1. 3) Re

389.4 GENERATOR REPLACEMENT – CONTINUED FIGURE E FIGURE F8) Remove the nut from the other side of the generator bracket (Figure E). 9) Loosen and r

399.5 GENERATOR BELT REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the front disks from the machine as outli

409.6 DRIVE BELT REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the front disks from the machine as outlined

419.7 PULLEY AXLE SET REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove both front disks from the machine as out

429.8 DRIVE AXLE SET REPLACEMENTNOTE:AMatrixspecialtoolisneededtocorrectlyreplaceadriveaxle.Orderpart#0000094817fromMatrixCTSat

439.8 DRIVE AXLE SET REPLACEMENT - CONTINUED10) The drive axle should have come with an iron plate installed (Figure G). 11) Assemble the Matrix to

449.8 DRIVE AXLE SET REPLACEMENT - CONTINUED16) Turn the nut until the iron plate is close to the frame on the right side (Figure M). 17) Remove th

459.8 DRIVE AXLE SET REPLACEMENT - CONTINUED22) Use a screwdriver to remove the iron plate from the drive axle (Figures S & T). 23) Re-install

469.9 CRANK REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the front disks from the machine as outlined in Se

2console serial number location1.1 SERIAL NUMBER LOCATION - CONTINUEDCHAPTER 1: SERIAL NUMBER LOCATIONSN # PLACEMENT

479.10 CONSOLE REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the 5 screws that hold the console to the top

489.11 OVERLAY & KEYPAD REPLACEMENTnote: The instructions below are for console overlays / keypads replacement, but the procedure is the same reg

499.11 KEYPAD & OVERLAY REPLACEMENT - CONTINUEDFIGURE E FIGURE FFIGURE G7) Peel part of the protective film from the back of the overlay (Figure

509.12 CONSOLE MAST HANDLEBAR REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the 4 bolts that hold the handl

519.13 DUAL ACTION HANDLEBAR REPLACEMENT1) Remove the plastic cover where the dual action handlebar meets the link arm (Figure A). 2) Remove the bo

529.14 FOOT PEDALS REPLACEMENT1) Pull up on and remove the rubber portion of the pedal (Figure A). 2) Remove the 4 screws that hold the plastic pe

539.15 PEDAL ARM REPLACEMENT1) Remove the plastic cover where the pedal arm attaches to the crank (Figure A). 2) Disconnect the pedal arm from the

549.16 LINK ARM REPLACEMENT1) Remove the plastic cover where the dual action handlebar meets the link arm (Figure A). 2) Remove the bolt and bushin

559.17 SWING ARM REPLACEMENT1) Remove the bolt from the upper pivot joint on the swing arm (Figure A). 2) Remove the plastic cap from the swing arm

569.18 VERTICAL STABILIZER ARM REPLACEMENT1) Remove the bolt that holds the vertical stabilizer arm to the frame (Figures A & B). 2) Remove the

32.1 READ THESE INSTRUCTIONSThis Suspension Elliptical is intended for commercial use. To ensure your safety and protect the equipment, read all instr

579.19 INCLINE ARM COVER REPLACEMENT1) Remove the screw that holds the plastic cover on the arm (Figures A & B). 2) Remove the incline arm cove

589.20 HANDLEBAR SERVICE1) All items on the handlebar are removed using a Phillips screwdriver from the underside of the bar. 2) Once the screws ar

599.21 TESTING THE SUSPENSION ELLIPTICALONCE THE UNIT OR REPLACEMENT PART IS FULLY INSTALLED AND ASSEMBLED AND PROPERLY PLACED ON THE FLOOR, USE THE F

6010.1 SUSPENSION ELLIPTICAL SPECIFICATIONSCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDEMODEL NAMEMODEL TYPE E5X ELLIPTICALFRAME

6110.2 ASSEMBLY HARDWAREQUANTITY SKETCH DESCRIPTION PACKAGE COLOR4SOCKET HEAD CAP SCREW(M10 X 1.5P X 25L)10.9 GRADE MINIMUMRED (2 BAGS)4FLAT WASHER(10

6210.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPSSTEP 1CHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6310.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 2 - RED HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6410.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 3 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6510.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDTorque this bolt to 80 N-m.STEP 4 - GREEN / YELLOW HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICA

6610.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 5 - RED HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

42.2 ELECTRICAL REQUIREMENTSGROUNDING INSTRUCTIONS:The Matrix E5x-04 Suspension Elliptical must be grounded. If it should malfunction or break down,

6710.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 6CHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

6810.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 7 - BLUE / BLACK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY

6910.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 8 - WHITE HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

7010.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 9 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

7110.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 10 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

7210.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 11 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

7310.3 SUSPENSION ELLIPTICAL ASSEMBLY STEPS - CONTINUEDSTEP 12 - PINK HARDWARE BAGCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE

7410.4 LEVELING THE SUSPENSION ELLIPTICALstabiliZinG tHe matriX susPension elliPticalThe Matrix Suspension Elliptical should be level for optimum use.

7510.5 TV BRACKET INSTALLATION INSTRUCTIONSThe Matrix Suspension Elliptical is capable of having a MYE Entertainment or Web Ready (PCTV) television in

7610.5 TV BRACKET INSTALLATION INSTRUCTIONS - CONTINUED6) Run the white end from the Y cable through the headphone jack hole in the console plastic, a

5CHAPTER 3: PREVENTATIVE MAINTENANCE3.1 RECOMMENDED CLEANING TIPSIn order to maximize life span, and minimize down time, all Matrix Fitness Equipment

7710.5 TV BRACKET INSTALLATION INSTRUCTIONS - CONTINUEDCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE12) Press the entertainment

7810.5 TV BRACKET INSTALLATION INSTRUCTIONS - CONTINUEDCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE18) There should now be 4 wi

7910.5 TV BRACKET INSTALLATION INSTRUCTIONS - CONTINUEDCHAPTER 10: SUSPENSION ELLIPTICAL SPECIFICATIONS AND ASSEMBLY GUIDE25) If installing a PCTV, pl

8011.1 SOFTWARE UPGRADE PROCEDURECHAPTER 11: SOFTWARE UPGRADE PROCEDUREFIGURE DFIGURE CFIGURE BFIGURE A1. Create a file on the USB flash drive which w

81NOTES

MATRIX FITNESS SYSTEMS CORP.1610 LANDMARK DRIVE COTTAGE GROVE WI 53527 USATOLL FREE 866.693.4863 www.matrixfitness.com FAX 608.839.1717REV. 01KO

6CHAPTER 3: PREVENTATIVE MAINTENANCE3.3 CARE AND MAINTENANCE INSTRUCTIONIn order to maximize life span, and minimize down time, all MATRIX equipment r