Matrix Setu ATA211G Especificaciones Pagina 20
- Pagina / 184
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
14 Matrix SETU ATA211G System Manual
• Remove the SIM Card from the Mobile Handset.
• Insert the SIM Card in to the SIM Holder of SETU ATA211G.
You may change the SIM PIN to the desired value after system installation is completed. You can change the SIM
PIN from Mobile Port parameters page of Jeeves. See “Mobile Port” under Basic Settings for instructions.
• Insert SIM Card into the SIM holder of the Mobile Port of SETU ATA211G. To do this,
• press the SIM holder lock (the small yellow button). You may use a blunt pin to press the lock button.
• the SIM holder tray emerges from its slot.
• pull out SIM holder tray from its slot.
• now, fit the SIM Card on the tray, with its contact side facing up.
• insert the SIM holder tray back into the slot.
• Connect the power adapter provided with SETU ATA211G to the power jack labeled 12VDC-1A(MAX).
• Connect the adapter plug into a power outlet.
• Switch ON power.
• Wait for the Reset Cycle to complete.
Reset Cycle
• At Power ON,
• The Power LED will glow green continuously.
• All other LEDs - FXS, Mobile, SIP1 and SIP2 will glow Red for ms, where xxx time depends on the
timing cycle from boot loader program to init sequence.
• After few seconds of Power ON, the Mobile LED starts blinking red. It indicates the network availability.
• On successful completion of initiation cycle, each LED will glow as per the events summarized in
the table below:
Meaning of LEDs
LED Status Meaning
FXS ON IC Call/OG Call - Speech and Off hook
Blinks Fast Error condition during IC/OG call
Blinks Slow IC Call: Ring Event OR OG Call: Number being dialed (after the end of
dialing)
OFF FXS port ON-Hook
Press the yellow button
to release the SIM holder.
Insert SIM with contact side
facing up.
- SETU ATA211G 1
- System Manual 3
- Documentation Disclaimer 4
- Contents 5
- Introduction 7
- Instructions 8
- Cross-references 8
- Terminology 8
- Know Your SETU ATA211G 11
- Ports and Connectors 12
- Applications of SETU ATA211G 14
- IP Network 15
- Getting Started 17
- Mounting the SETU ATA211G 18
- Connecting SETU ATA211G 19
- Press the yellow button 20
- Insert SIM with contact side 20
- Configuring SETU ATA211G 22
- Configuring using a Phone 25
- Configuring Basic Settings 27
- 1. Click Region 29
- SIP Trunks 31
- Trunk Settings 32
- Incoming Call 35
- Vocoders 39
- Advanced 40
- Mobile Port 44
- FXS Port 54
- Outgoing Call 55
- Class of Service 58
- Passwords 62
- Changing User Password 63
- DNS Server 67
- Advanced Settings 69
- System Parameters 70
- Called Party Number Table 75
- 4. For each Index number 76
- Dialed Number Table 77
- Peer-to-Peer Numbers 80
- 001 No Match Found 01 24 81
- 002 3 04 04 190.1.1.100 81
- Making Peer-to-Peer Calls 83
- Mobile Emergency Numbers 84
- Digest Authentication 86
- PIN Authentication 89
- 3. Click PIN Authentication 90
- Daylight Saving Time 91
- as 60 minutes 93
- Static Routing 94
- 3. Click Static Routing 95
- Reinstate Factory Defaults 97
- Restart SETU ATA211G 99
- 3. Click Syslog 100
- 1. Log in as User 101
- 1. Log in as Admin 102
- 3. Click PCAP 102
- 9. You may log out of Jeeves 104
- Software Upgradation 105
- Auto Configuration 106
- Features of SETU ATA211G 109
- Making a Second Call 110
- Call Transfer 111
- Call Toggle 113
- Call Waiting 114
- Using Call Waiting 115
- Conference 117
- Do-Not-Disturb 118
- Using Phone 119
- Call Forward 120
- Caller ID Restriction 124
- Using Commands 125
- Selective SIP Trunk Access 126
- Speed Dialing 127
- Configuring Speed Dialing 128
- Multi Stage Dialing 135
- End of Dialing 140
- Mobile Network Selection 141
- About Network Operator Codes 142
- How it works? 143
- Configuring RCOC feature 144
- 5. Click Submit to save 145
- System Status 147
- Network Parameters 150
- Date &Time 152
- Firmware 152
- Appendix 155
- Ring Cadences 156
- Acronyms 161
- Features at a Glance 163
- System Commands 164
- Product Specifications 166
- Dimension (W x H x D) 168
- Power Supply 168
- Environmental 168
- Warranty Statement 169
- Regulatory Information 171
- Version 2, February 2011 184
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales